That surprises me, but I suppose it had to work for some listeners or they wouldn’t have gotten it past testing. I have even tried clearing my listen history and starting over - still comes up with country and (going to clarify) ‘metal’ . I like rock and alternative and some forms of pop, as well as a bit of hip hop. cannot fathom why it suggests what it does.
What is rym?
I have started buying vinyl with the digital downloads when I find a great album. I feel better doing it this way. Most of my music is not super big name artists.
I know this does not make me look good - but I am a YouTube Premium subscriber. I had Spotify, but they jacked up their family plan rate, and it was only a few bucks cheaper than Premium, then I got the ad-free (without adblockers). I mostly did it to help my kids avoid the toxic ads that are littered into the kid content. The main reason I stick with some of this stuff is for the discovery. Pandora was great, Spotify is ok.
Regardless - the smart playlists, and AI stuff on YouTube music is AWFUL. I cannot put into words how bad it is. Spotify got it right about 1/4-1/2 of the time. YouTube, maybe 1/100. Constantly recommending a country, which I cannot stand. When it isn’t doing country, it recommends hard rock/metal which I also do not listen to. I feel like I need a new way to find music, then I could sever ties with all these trashy subscriptions.
So…something like 3d printing…
Worked in retail many moons ago. Back when organic was just becoming a thing. I can tell you one thing.: A lot of people were getting a deal on organic food -because cashiers would just key in the code for non-organic. The lines were too long, and you look foolish looking things up in the “book” haha.
It’s funny to me…I didn’t say they were bad, I didn’t say I didn’t like them, I didn’t say anything except for that they clearly took their music in a more in your face, political direction. That’s fine, I support them making that choice. I get that punk is inherently political, and that most music has hints of it. When I started listening, when 1039 came out - I was too young to understand what the music was about. Then came kerplunk and dookie. Dookie has many songs that are just about boredom, wasting time, or girls. Same thing for Insomniac and Nimrod. You cannot argue that EVERY song on those albums was political, it’s just not true. They became a pop-punk alternative band. That’s great, they still make great music, I just choose other styles and genres. Downvotes aren’t hurting me, but it seems excessive for sharing my thoughts.
For the record, I was a ride or die fan in the 90’s. 5 shows, one of them I waited by the outdoor stage for 3 hours to get a good spot. I had my art featured on the earliest version of their website, back in the AOL days. I still love the music I grew up with. Bands style, peoples preferences change…I just don’t want to think about the broken world when I listen to music anymore.
Correct. I was struggling with a design …(I am very new to cad) I normally would have gone to reddit, but since I quit reddit with the drama, I came here. Not much going on so I had to look elsewhere. I didn’t make the channel, I think it is an official channel. Maybe…? Regardless. They have helped me a ton. One of the users actually recreated my design the “proper” way so I could achieve what I needed.
It’s not anymore. You’re very correct.
It’s funny - I agree with Green Day in most ways politically, but stopped listening after American Idiot because so much of their music was blatantly political. That’s what they were going for, it is CLEAR and OBVIOUS to anyone listening to their music, where they stand. I am all for it, I would just rather be escaping the world’s issues while listening to music :)
I forgot until looking at your photo that the mini uses a Bowden tube, not direct drive like the MK3S+. Did you replace/switch the nozzle around the time this all started happening? With Bowden tubes, there are a few problems that can arise that you don’t see on direct drive. The end of the Bowden tube (that is inside the extruder/hote end assembly) can get deformed or clogged. If you can check that, you may find an issue. Other than that, when swapping nozzles I always had to put the nozzle in part of the way, then push the Bowden in further, then tighten the nozzle.
My money would be a clogged nozzle. But a better photo (close up) may be helpful. Things I wonder…
Does the filament come out and curl back up during preheat?
Is your heat block messy with residue?
Have you tried a cold pull, or pulling the nozzle and cleaning/replacing it?
Not sure what that means. I never get any messages from TMO unless it’s a bill notification…
Amen.
Anyone try this one? I want it for the VR…curious how well the controls works .
deleted by creator
It would be great if Lemmy’s devs implemented loosely based (for fair use) copies of these and gave them for free :)
What is an appimage?
When I first started working with 3d modelling (for 3d printed parts), I followed everyone’s advice and got a trial of Fusion. Luckily, I didn’t use it much and when I came back to it, my trial was over. I did not want to use a hobbyist license, just to have things change - so went looking for FOSS alternatives. OpenScad made my brain hurt, but then I found FreeCAD. Definately hard to learn, and for someone new to CAD design - I am learning very slowly.
I watched a ton of videos, but still struggle. My saving grace was that I found the official discord. The users on the discord server can be super helpful with learing the nuance of the platform. Several times I posted a file and askded for help and had an answer within an hour. In fact, I just submitted a screenshot of my sketch with dimensions and someone went ot the trouble of recreating it and fixing my problem…so I recommend you join the server if you are struggling. Link below:
Every time. I am not sure it actually changes anything. I have submitted feedback and bug reports to YTM as well. Just generic replies.