• Aceticon@lemmy.world
    link
    fedilink
    arrow-up
    9
    arrow-down
    1
    ·
    edit-2
    1 year ago

    You could just use 2 Ethernet Over Power adaptors (not to be confused with power over ethernet).

    After all, it’s not as if the powerlines aren’t already installed at home and connect all power plugs with all other power plugs.

    This isn’t even new: I’ve been using this solution for about a decade, back when it could do a mere 20Mb/s (which was still way faster than my Internet connection could handle back then ;))

    Unless having a 500Mb/s limit on bandwith is somehow unacceptable when you could have Gigabit ethernet. Then again, why not fibre all the way ;)

    • Entheogen@lemmy.world
      link
      fedilink
      arrow-up
      12
      ·
      1 year ago

      Have you ever paid attention to packet loss?

      Honest question, because I’m an electrician and Ethernet is so fickle, I’ve always assumed it would play hell on the overall quality.

      • Aceticon@lemmy.world
        link
        fedilink
        arrow-up
        10
        arrow-down
        1
        ·
        edit-2
        1 year ago

        The whole thing is layered into multiple levels (go check the OSI Model and its Layers on Wikipedia if you’re willing to go down that specific information hole ;)) and the physical layer should mainly be handling packet loss on the connection between those adaptors, transparently to the higher layers that just see that as lower bandwidth than the spec for the adaptors (a spec which is really quite optimistic, IMHO).

        Yeah, a cable with a metal sheaf wired to the GND level (i.e. Cat cable) is going to be way better at higher frequencies and at isolation from noise that two twisted copper wires were the network signal is shared with a different “signal” which whilst generally 50/60Hz (depending on country) can have spikes and noise at other frequencies, so it’s never going to be the same.

        However for example at home right now I can get a reliable 100 Mbit/s over a pair of those adaptors from my router to my PC and the speed limitation is actually (I believe) from my old router not supporting Gigabit Ethernet rather than from the adaptors which are supposed to handle up to 500 Mbit/sec.

        That said and as somebody pointed out, it only works well if the plugs you’re connecting are on the same electrical network, as transversing coils isn’t exactly great for high frequency signals.

        • ramjambamalam@lemmy.ca
          link
          fedilink
          arrow-up
          3
          ·
          1 year ago

          it only works well if the plugs you’re connecting are on the same electrical network, as transversing coils isn’t exactly great for high frequency signals.

          What does “electrical network” mean? Panel? Circuit?

          • Aceticon@lemmy.world
            link
            fedilink
            arrow-up
            2
            ·
            edit-2
            1 year ago

            If two plugs are connected to different circuit breakers, then they’re in different “electrical networks” in this sense: basically for a signal to go from one such plug to the other one it has to transverse both circuit breakers and that means going through coils.

            Coils are inductors, which are electrical elements which have have frequency dependent resistance (in simple terms), with the higher the frequency of a signal the more the resistance they offer to the passing of a signal, and the higher the bandwidth of your data connection the higher the frequency of the signal(s) necessary to transport that data.

              • Aceticon@lemmy.world
                link
                fedilink
                arrow-up
                1
                ·
                1 year ago

                I learned this stuff in a different language so don’t really know the right terminology in English.

                Also I’m from the Electronics side, so for me a “circuit” is something quite different ;)

      • Fordry@lemmy.world
        link
        fedilink
        arrow-up
        2
        ·
        edit-2
        1 year ago

        It definitely can be finicky. I had a portable ac that completely killed the power line ethernet connection when it ran. And my current house I have it in i use from where my router is to where my main TV is and it is unreliable even without that AC unit. So it definitely depends on the circumstances.

      • vpklotar@lemmy.world
        link
        fedilink
        arrow-up
        1
        ·
        1 year ago

        I used ehternof power for many years and although I didn’t look at packet loss I never had a problem with it.

    • BRabbit@lemmy.world
      link
      fedilink
      arrow-up
      5
      ·
      1 year ago

      My experience is that you need to be sure the outlets are on the same electrical network, otherwise it doesn’t work. When I did get it to work it seemed to be reliable.